[Solved!] Why Massey Ferguson PTO Not Engage?

massey ferguson pto not engage

A disengaging PTO is considered as a threatening sign for the Massey Ferguson tractor. But, the concerning matter is what causes this issue that hinders in operating the tractor.

So, what makes Massey Ferguson PTO not engage?

The reasons are the PTO switch out of duty, wires are damaged or corroded, damaged or misadjusted PTO clutch, battery delivering less voltage or power, and the malfunctioning PTO clutch.

When you know the reasons behind Massey Ferguson PTO not engage, you can solve it quickly and with smart solutions.

So, stick to the article till the end.

Quick Overview: Massey Ferguson PTO Not Engage?

A short description of the causes of Massey Ferguson PTO not engage will drive you quickly in detecting them. They are listed in the following table with the correct fixes.

Therefore, don’t forget to take a look at it.

Serial            Reasons                        Solutions
1PTO switch out of dutyCheck the PTO switch and replace it
2Wires are damaged or corrodedClean the wires and get new ones if needed
3Damaged or misadjusted PTO clutchAdjust the PTO clutch or get it changed
4Battery delivering less voltage/powerClean the battery terminals and replace the battery
5Malfunctioning PTO shaftFollow a cleaning procedure of the PTO shaft and change the linkage

Detailed Talk: Massey Ferguson PTO Not Engage?

Certainly, the table will guide you in catching the reasons in a short course and let you decide the primary fixes. However, for a long lasting and effective way, this section is filled with their descriptions.

That’s why check out the reasons and solutions one by one.

Reason 1: PTO Switch Out of Duty

A defective PTO switch is one of the most common reasons. Because it prevents the PTO from working in the regular way.

If the switch is bad, it won’t provide the PTO the command that you are sending it to engage. The switch can have burnt wires or get damaged.

Solution: Check the PTO Switch and Replace It

Checking the PTO switch is required before you proceed with any changes. Its wires can be changed in case any irregularities are noticed.

If they are alright, the switch is possibly bad. Get a new PTO switch for your Massey Ferguson.

Reason 2: Wires are Damaged or Corroded

As the PTO is an electric powered unit, it has a connection with the tractor’s electric unit through wires. But, over time, the wires can get damaged due to getting cracks or getting in touch with sharp metals.

Corrosion can start living on their body and prevents the PTO from getting power.

Solution: Clean the Wires and Get New Ones If Needed

Cleaning the PTO wires on a regular note should be a part of the tractor’s maintenance. It ensures they are working perfectly keeping dirt away.

If the corrosion has affected the wires badly, get new ones matching with them.

Reason 3: Damaged or Misadjusted PTO Clutch

A PTO clutch that is not adjusted in the correct position won’t assist the PTO in engaging. As its functioning depends on the PTO clutch, it should be in the accurate position.

Another noteworthy reason is the damaged or bent health issues of the PTO clutch. All these pressurizes it to guide the PTO in failing to stay in disengaging position.

Solution: Adjust the PTO Clutch or Get It Changed

First, take the owner’s manual and adjust the PTO clutch following the instructions. In this way, mistakes can be avoided.

If adjustment is not making any effects, get the PTO clutch changed without a second thought.

Reason 4: Battery Delivering Less Power/Voltage

Nowadays, every Massey Ferguson tractor has an electric PTO system and it requires enough voltage or power from the battery to function.

But, a battery with corroded wires or bent terminals won’t be able to deliver that required voltage to the PTO system. And for that reason, it doesn’t engage with the command.

Solution: Clean the Battery Terminals and Replace the Battery

First, take a dry clutch and clean the battery wires from each joint and do the same for the terminals. If any of them is bent, replace that immediately.

As for the battery, any major fault in it won’t let it charge. At this point, replacing it would be a wise move.

Reason 5: Malfunctioning PTO Shaft

A faulty PTO can be caused by a malfunctioning PTO shaft. The PTO shaft can be stuck due to the uncleaned condition of it for an extended course.

Another reason is the linkage that is placed close to the shaft can get injured or bent. It causes the disconnection between the shaft and the shifter. Thus, the PTO tries but fails to engage.

Solution: Follow a Cleaning Procedure of the PTO Shaft and Change the Linkage

As for the PTO shaft, cleaning it regularly will drive away the stuck situation. Avoid leaving anything near the PTO shaft for a step ahead protection.

Check the linkage to observe its actions and try to repair it. In case that is not possible, go with replacing the linkage.

Why Won’t My Massey Ferguson PTO Won’t Engage?

Answer: A Massey Ferguson PTO fails to engage due to the battery providing less power than required. Without power, the PTO refuses to engage the way it usually does.

How Do I Adjust My PTO Pressure?

Answer: You can adjust the PTO pressure just by setting the allen wrench on the valve stem and rotate it. Placing it in an up position offers more PTO pressure and in a down position for stopping more pressure.

Final Verdict

To keep you Massey Ferguson away from PTO engaging issues, the article has got your back. To be honest, PTO issues are not at all an event to be ignored.

Luckily, everything is included in it with the in-depth details of Massey Ferguson PTO not engage. However, make sure to follow the solutions carefully to avoid the mistakes.

Related Posts:

Scott McFadden

Hi! It's Scott McFadden. I'm obsessed with farming. All my life I grew up around my grandfather and his farmhouse. I cannot put in words how they inspired me to farm. From taking care of cows to looking after our gardens I have learned a lot. It would be a real pleasure if I get to share this with you.

Recent Posts