A faulty carburetor in a Briggs and Stratton push mower carburetor will leave the mower shut off completely. Any defects in its parts can hamper its function.
But, what are the essential parts of a Briggs and Stratton push mower carburetor?
They are the air correction jet, idling air jet, throttle lever, pump jet, injection tube, starter fuel jet, idling adjusting screw, and pump cylinder.
You won’t understand much just by their names. That’s why a Briggs and Stratton push mower carburetor diagram is depicted here with each parts introduction.
So, don’t miss it, buddy.
What Are the Symptoms of a Bad Carburetor on a Push Lawn Mower?
The carburetor on a push lawn mower lets you push the mower by getting the engine on duty. But, a bad carburetor fails to do that and you may not realize it as the signs of a bad carburetor vary.
So, here are the signs of a bad carburetor on a push lawn mower described for you.
1. Zero Idle of Engine
Zero idling of the engine on a push lawn mower is a direct symptom of the carburetor being bad.
It is because due to the improper mixing of fuel and air, the carburetor delivers a wrong mixture to the engine. Consequently, the engine won’t idle with this fuel and may start stalling.
2. No Acceleration Detected
With the command for acceleration, the carburetor has a duty to deliver more fuel to the cylinders.
But, once it works with a faulty component, the flow to the cylinder may not increase or completely stop. As a result, the acceleration of a push lawn mower is not detected.
3. No starting of Engine
The engine on a push lawn mower facing toughness in starting means the carburetor has some issues.
The starting problem rises when the carburetor gets less air flow than the fixed ratio. And, that is caused by the carburetor’s damaged components.
4. Black Smoke
Black smoke getting emitted from the exhaust hose is an easier indication that the carburetor is working with irregularity.
As it doesn’t mix the fuel and air as per as required, the black smoke is encountered. And, it will continue to come out till the carburetor mixes the fuel and air correctly.
5. Imbalanced Running
Imbalanced running of your push lawn mower is mostly invited by a carburetor that is not delivering enough fuel.
The mower may start but the running performance deteriorates as the carburetor gets difficulties in flowing the mixture. Since the flow is not regular, the mower follows a rough running.
What to Check Before the Briggs and Stratton Push Mower Carburetor Diagram?
Though the diagram is necessary, knowing the Briggs and Stratton push mower engine specs will enhance your concepts.
Continue reading and check them out.
• Engine Type: Gasoline
• Number of Cylinders: Single
• Gross Torque: 4.5
• Stroke: 1.75 Inches
• Starter Type: Pull
• Fuel Tank Capacity: 0.2 Gallon
• Oil Tank Capacity: 15 Oz
• Displacement: 125 CC
• Bore: 2.36 Inches
• Air Filter: Oiled Foam
• Weight: 17 lbs
• Engine Configuration: Vertical Shaft
Now that you have met the specs, the diagram is calling you.
Briggs and Stratton Push Mower Carburetor Diagram
Your waiting has come to an end as the Briggs and Stratton push mower carburetor diagram is given below.
Catch a sight of it along with the parts locations.
From the right side of the diagram, there is a pump cylinder, air correction jet, idling air jet, dual float, with toggle, lower pump levet, idling jet and main jet.
At the top of the carburetor, the mixture tube with diffuser is beside the holder, and the fixing screw for mixture tube holder is noticeable just close to them.
Then comes the pump jet, injection tube, starter fuel jet, idling adjusting screw, throttle spindle and throttle lever are pretty close, and two of idling mixture regulating screws.
Now, it is time for driving to a broad way to learn about the parts.
So, go through the Briggs and Stratton push mower carburetor parts list.
1. Air Correction Jet
The air correction jet is for letting air come into the carburetor and get in touch with the fuel.
2. Idling Air Jet
When the push mower engine is idling, the air and fuel mixture is affected by this idling air jet.
3. Throttle Lever
This throttle lever is for having a control on the carburetor in the case of delivering fuel in an appropriate amount.
4. Pump Jet
The purpose of the pump jet is seen when the carburetor requires more gasoline to run the engine.
5. Injection Tube
Injection tube or fuel injection line is for injecting the needed fuel to the carburetor maintaining the pressure.
6. Starter Fuel Jet
If the engine is cold and hard to start, the starter fuel jet will increase the flow of fuel and air to become a rich mixture.
7. Idling Adjusting Screw
When you balance an idle speed, the idling adjusting screw will ensure the idle vacuum is sufficiently developed.
8. Pump Cylinder
The pump cylinder is for fulfilling the requirement of extra fuel of the carburetor by pumping more.
What is the Carburetor on a Briggs and Stratton Push Mower?
Answer: The carburetor on a Briggs and Stratton push mower guides the engine to operate freely. It gets fuel and air and mixes them well and lets them flow to the engine. Thus, the combustion process is done by its help.
What are the Symptoms of Briggs and Stratton Push Mower Bad Carburetor?
Answer: The symptoms of a bad carburetor on a Briggs and Stratton push mower are the muffler releasing black smoke, engine stops as soon as the mowing starts, and white smoke comes from the mower.
End Words
To be honest, the Briggs and Stratton push mower carburetor diagram will assist you much in inspecting the diagram. As the positions of every part are illustrated, you can know about their conditions.
Moreover, any issues can be discovered effortlessly just by checking them. As for the maintenance, that has already become easier for you.
Related articles: