Briggs and Stratton Lawn Mower Governor Spring Diagram

briggs and stratton lawn mower governor spring diagram

At a point, the Briggs and Stratton lawn mower governor problems will demand you to check its spring to fix them. But, not everyone has a map in their mind to locate the spring.

Because too many tiny to small types of components are there. Troubleshooting the governor spring also becomes tough if you have zero clue of its whereabouts.

For that reason, I have included the Briggs and Stratton lawn mower governor spring diagram in this article. The details of it will surely guide you to take care of it.

So, let’s get started.

What to Learn About Before the Diagram?

Be sure that you will get the diagram with the niceties. But, before that, here are some Briggs and Stratton specs that you should learn about.

So, take a glance at them.

1. Engine

• Engine Style: Vertical

• Cylinder: 1

• Engine Type: 4 Cycle OHV

• CC: 140 CC

• Horsepower: 3.75 HP

2. Others

• Cooling System: Air

• Air Cleaner: Foam

• Oil Capacity: 16 oz

• Crankshaft Rotation: Counterclockwise

• Starting System: Recoil

• Ignition: Electronic Spark

• Muffler: Built-in

I guess it is the exact time to drive you ahead to the diagram.

Briggs and Stratton Lawn Mower Governor Spring Diagram

After reaching the Briggs and Stratton governor unit, you may get confused about where the spring is.

Well, catching sight of the Briggs and Stratton lawn mower governor spring diagram, you can easily locate it.

The diagram is illustrating the governor spring (209), governor idle spring (211), governor link (632), screw (188, 267, 564, 663A), link control (410), switch stop (621), spacer (668), washer set friction (504), and lever control (271A).

Next parts are the retainer (773),  bracket control (222), sleeve lever (843), panel control (281), control wire (269), control wire casing (268), clamp casing (265), and nut (270, 505, 1138, 1404). 

The last ones are the lever go control (227), bolt (562), washer (278), governor retainer shaft (615), governor crank (616), stud (1230), and cover control (604A).

The diagram is undoubtedly an effortless way to get access to the governor spring.

Now, I suggest you go through the Briggs and Stratton lawn mower governor spring parts list.

1. Governor Spring

The governor spring has the job of letting the throttle open and helping in balancing RPM. 

2. Washer

The secured tension of a center bolt is completely dependent on the washer.

3. Governor Idle Spring

Governor idle spring is considered the secondary governor spring that has connection with the governor.

4. Governor Crank

The governor crank has an influence in balancing the engine speed.

5. Governor Link

Governor link is one of the important parts of the governor unit.

6. Lever Control

The lever control is for operating the ignition to start the engine.

7. Governor Retainer Shaft

The governor retainer shaft performs the duty of closing the throttle to decrease the RPM.

What is the Briggs and Stratton Governor Spring Connected To?

Answer: The Briggs and Stratton governor spring is connected to the governor throttle linkage arm. Through this arm, the governor spring operates the opening function of the throttle. Also, the RPM of the engine is controlled in this way.

Why is There a Governor Spring Adjustment?

Answer: A governor spring adjustment is required to have a control on the speed of the engine. The workload of the engine at any terrain is maintained with the adjustment. But, the governor spring adjustment should be accurate.

End Note

In short, you have no other better way than a Briggs and Stratton lawn mower governor spring diagram. Because it is of efficient help when you are trying to figure out which one is the governor spring.

Moreover, use this diagram when you are about to clean or troubleshoot or take care of the spring. It lets you prevent unwanted troubles to the components.

Scott McFadden

Hi! It's Scott McFadden. I'm obsessed with farming. All my life I grew up around my grandfather and his farmhouse. I cannot put in words how they inspired me to farm. From taking care of cows to looking after our gardens I have learned a lot. It would be a real pleasure if I get to share this with you.

Recent Posts